







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Door Installation in Irvine, CA: What It Takes and What It Costs
Door installation in Irvine, CA typically runs $650 to $4,200 per door, depending on whether it’s an interior slab swap, an exterior entry door, or a commercial-grade storefront opening, and most single-door jobs wrap in one to two days. The number moves with material, frame condition, and whether the village’s architectural committee has to sign off before we start. Call (855) 532-8973 for a free on-site estimate and a written, line-item quote.
How our door installation process actually runs, day by day

Every door we install moves through the same five stages. The time frames below hold for a standard single-door job; stacked or multi-door orders stretch the demo and finish phases but the sequence never changes.
Stage 1: Measure and site check (day 1, roughly 60 to 90 minutes)
We measure the rough opening in three places – top, middle, bottom – because Irvine tract homes settle unevenly and a doorway that reads 32 inches at the header can run 31 5/8 at the threshold. This is also when we check the existing frame for rot, water damage, and whether the wall carries load above the header. You’ll decide door swing direction and handing during this visit. Getting handing wrong is the single most common ordering mistake, and it costs two to three weeks to correct.
Stage 2: Ordering and HOA/design review (5 to 21 days, homeowner-driven)
For exterior doors in Irvine, your village architectural committee almost always has to approve the style, color, and material before we cut anything. Woodbridge and Northwood both run design review through their community associations, and Turtle Rock and Quail Hill add slope and grading considerations on top. We prepare the submittal specs – dimensions, finish color, glass package – and you sign. Interior doors skip this entirely and can order same-day.
Stage 3: Demo and rough prep (day 2, three to five hours)
We pull the old door and frame, inspect the jack studs, and shim or sister framing where it’s soft. On 1970s-to-1990s Irvine homes, we regularly find the original sill pan installed with no back-dam or end-dams, which means water has been wicking into the subfloor for years. We build a proper sill pan with flashing tape and a sloped sill before the new door goes in. This is the part that protects you against the Santa Ana-driven rain that hits Irvine a few times each winter.
Stage 4: Set, shim, and weather-seal (day 2 to 3, four to six hours)
The door gets set plumb and square, shimmed at the hinge and strike sides, and tested through 20 to 30 open-close cycles. We foam the perimeter, tape the flashing, and set the exterior trim. For entry doors, that means installing the lockset, deadbolt, and any rolling-code opener hardware. We test the strike plate alignment by hand, not by eye.
Stage 5: Finish, inspection, and walkthrough (day 3, two to three hours)
Interior casing, threshold, and any drywall patch go in. If your door touches a structural opening or changes the building envelope, an Irvine building inspector signs off before we close the wall – we schedule the inspection and meet the inspector on site. We walk you through the door operation, hardware, and the warranty before we leave. Every job is covered under our 730-Day Done Right Promise, so if something shifts in the first two years, we come back and make it right.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The door options Irvine homeowners actually choose between
The spec sheet is where jobs run high or low. Here’s the honest trade-off on each:
- Fiberglass entry doors: The default for Irvine’s sunny, semi-arid climate. Won’t warp, dent, or split under thermal cycling, and takes paint well. Runs $1,400 to $3,200 installed for a single door. Best choice if you have west- or south-facing entry exposure.
- Steel entry doors: Strong, secure, and good for security-focused openers with rolling-code deadbolts. But steel dents and shows every impact. $1,100 to $2,600 installed. We only recommend it for protected entries.
- Wood entry doors: Warmest look and pairs best with the Mediterranean and Spanish-style stucco homes throughout Irvine. It swells and contracts with seasonal humidity and needs refinishing every three to four years. $1,800 to $4,200 installed.
- Interior hollow-core doors: The standard for bedroom and closet doors. Light, cheap, easy to hang. $450 to $850 per door installed. Fine for closets, less so for anything with traffic.
- Interior solid-core doors: Heavier, quieter, and better for a home office or bedroom near a shared wall. $750 to $1,400 per door installed. Worth the upcharge where sound matters.
- Hardware and openers: A standard Grade 2 lockset runs $80 to $250; rolling-code wireless openers and a matched deadbolt/handle set add $150 to $400. Cheaper hardware is the fastest thing to fail on a new door.
For exterior doors we work with established manufacturers that carry a real warranty, and the finishes we spec hold up under Irvine’s UV load. If you’re pairing this with a wider envelope upgrade, the Windows & Doors in Irvine page covers the larger scope.
What Door Installation costs in Irvine, CA

Door installation in Irvine lands between $650 and $4,200 per door, with the median exterior entry door running $1,400 to $3,200 installed. Here’s the line-item breakdown:
| Interior door, hollow-core, installed | $450 – $850 |
| Interior door, solid-core, installed | $750 – $1,400 |
| Exterior entry door, steel, installed | $1,100 – $2,600 |
| Exterior entry door, fiberglass, installed | $1,400 – $3,200 |
| Exterior entry door, wood, installed | $1,800 – $4,200 |
| Framing repair or sill-pan rebuild | $300 – $900 |
| Hardware and rolling-code opener/accessory | $80 – $400 |
The five variables that push a job toward the high end: existing frame condition (rotted jack studs or a failed sill pan add $300 to $900), door material (wood vs. steel spans more than $1,000), hardware grade, whether we’re moving the rough opening (always a permit item), and whether HOA architectural review requires a custom submittal package. What’s included in our written estimate: demo, disposal, framing repair up to a point, new sill pan and flashing, installation, hardware set, and full cleanup. What’s outside most quotes: HOA submittal fees, any trim or paint match beyond the door edges, and structural changes to the opening.
See the difference
Before
After
Before
After
Before
AfterWhat Irvine homes specifically do to door installation
Irvine is a master-planned city built largely by the Irvine Company from the 1970s onward, which means almost nothing on the exterior happens without a village-level architectural committee sign-off first. Woodbridge, Northwood, Turtle Rock, and Quail Hill each run their own design review before any exterior door hits a permit counter, and Irvine’s own building-permit process comes after. Contractors working in neighboring Santa Ana or Tustin don’t deal with that governance layer. We do, on nearly every Irvine door job.
The housing stock pushes the work toward the 1970s-to-1990s tract and semi-custom homes, where we see the same failure pattern: original entry doors with a flat sill, sun-cracked fiberglass skins from 30 years of UV, and stucco pulling away from the frame where thermal cycling has cracked the edge. The newer mid-rise and apartment complexes around the Spectrum and UCI have the opposite problem – doors that are only a few years old but were installed with undersized shims and open with a drag. We work in the 92602, 92617, 92619, and 92604 ZIP codes routinely, and cover the wider area under Irvine.
Serving Irvine, CA – Our Local Coverage Area
We serve Irvine and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently asked questions about Door Installation in Irvine

A standard interior door takes three to four hours; an exterior entry door takes one to two days, not counting the 5 to 21 days for ordering and HOA review. Multi-door jobs run proportionally longer. Call (855) 532-8973 to schedule a free on-site estimate and get a real timeline for your opening.
Yes for any exterior door and for any interior door that changes the rough opening or touches a load-bearing header; a straight interior door swap in the same opening does not need one. The exterior door also needs village architectural committee approval first. We pull the permits, meet the inspector, and stay through the sign-off.
Yes, if the opening is the same size and the framing is sound – the existing door comes out and the new one goes into the same rough opening. If the framing is soft or the header has sagged, we sister new studs or replace the header, and that adds $300 to $900 and requires a permit.
Between $650 and $4,200 per door depending on type and material, with a typical exterior entry at $1,400 to $3,200 installed. Frame repair, hardware upgrades, and HOA submittal fees push the number higher. Call (855) 532-8973 for an exact quote – estimates are free and written line-item, and the number we quote is the number you pay.
Our workmanship is covered by the 730-Day Done Right Promise – if it’s not done right, we make it right for two full years. The door manufacturer’s warranty on the unit and hardware runs alongside it. Both are in writing at the walkthrough.
Get a free door installation estimate in Irvine
Our team will visit, measure the opening, and hand you a written line-item estimate before you commit to anything – no change orders, no surprises. We answer the phone live, 24/7, and we’re happy to coordinate the HOA submittal for exterior doors. Call (855) 532-8973 to schedule your free estimate for Windows & Doors work, or to talk through a Cabinets & Countertops in Irvine or Garage Conversion ADU in Irvine project you’re planning alongside it.
Written by the team at Groundwork Construction Co.












